GE / IP FANUC Series 90/30 In Stock
Manufacturer: | Horner Electric |
Product Type: | Automation Product |
Part Number: | HE693PBM101 |
Series: | PLC I/O |
UPC: | 810946773568 |
Description:
The HE693PBM101 Profibus Master Module from GE Fanuc acts as a Profibus DP network master for Series 90-30 products. It can control a maximum of 64 slave devices and operates at a 24 megahertz frequency. It contains a 9-pin Profibus DP connector, a standard 9-pin RS-232 connector, and three visible LEDs to indicate master states and fault conditions. This module sends the PLC processor 64 bits of diagnosis and 64 bits of status information.
Automation Stop is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with Automation Stop's 1-year warranty.
We accept credit cards from all major providers, as well as PayPal.
We offer worldwide shipping with UPS and DHL.
We proudly offer a one year Automation Stop warranty on most products.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
The HE693PBM101 is a Profibus Master module by Emerson - GE Fanuc. It operates as a Profibus Decentralized Periphery (DP) network master. This module can control up to 64 slave devices, including input/output devices, drives, transmitters, and much more. It also enables Profibus-based communication across modules in various programmable logic controller racks. This module is designed to be inserted into the Series 90-30 local slot. It operates with a frequency of 24 megahertz. This module comes with a Profibus DP port. This port has a 9-pin D-sub plug connector. This D-sub connector allows establishing a physical connection between the slaves and the master. This Profibus master module also has an embedded RS-232 serial port that is used to upgrade the firmware of the slave. This service port is equipped with a typical 9-pin RS-232 connector.
Part number HE693PBM101 has three (3) LEDs, or light emitting diodes, that are visible to users. These include the OK, POWER, and RUN LEDs. The user can observe 6 possible combinations of these LEDs. Each combination will represent the different states of the master. For instance, when all LEDs are green, it indicates that the module is receiving good power and valid configuration from the CPU. Moreover, the module is also communicating properly over the Profibus-DP network. To determine the fault condition of the module, count the green pulses of the RUN LED in each cycle. This module transmits 64 bits of diagnosis and 64 bits of status information to the PLC processor. It requires 4 watts of power at 5 volts direct current.
Question: Does Automation Stop offer repairs on the HE693PBM101?
Answer: Yes. We offer repairs for the HE693PBM101 and it comes with our 1 Year Automation Stop Warranty.
Question: What type of warranty comes with the Horner Electric and HE693PBM101?
Answer: If you buy the HE693PBM101 through Automationstop.com it comes with our 1 Year Warranty and no other warranties.
Question: Can I buy the HE693PBM101 online?
Answer: Yes. Automation Stop sells the HE693PBM101 online and you can check out for the quantity and condition listed available above.
Question: What is the manufacturer for the HE693PBM101?
Answer: The HE693PBM101 is made by Horner Electric.
For additional information about HE693PBM101 check the data sheet or manual. Also check the manual PDF for all wiring diagrams, compatibility, troubleshooting, specifications, installation instructions, and accessories (such as batteries, terminal blocks, or cables) regarding HE693PBM101.
Revision Part # | Also Known As | Availability |
---|---|---|
HE693PBM101E | HE693PBM101 Series E, Rev E | Request a Quote |
Common Misspellings:
Automation Stop sells used surplus products. Automation Stop is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by Automation Stop come with Automation Stop’s 1-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.