GE / IP FANUC Series 90/30 In Stock
Manufacturer: | Emerson - GE Fanuc |
Product Type: | Automation Product |
Part Number: | IC200ERM002 |
Series: | Versamax |
UPC: | 888165908559 |
Description:
Designed and produced by Emerson - GE Fanuc, part number IC200ERM002 is an expansion receiver module. This module belongs to the VersaMax series of products and is non-isolated. This device is equipped with LED, or light emitting diode, indicators that are labeled PWR, EXP RX, and SCAN. This module has a backplane current consumption of 70 milliamperes at an output voltage of 5 volts, as well as 20 milliamperes at an output voltage of 3.3 volts.
Automation Stop is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with Automation Stop's 1-year warranty.
We accept credit cards from all major providers, as well as PayPal.
We offer worldwide shipping with UPS and DHL.
We proudly offer a one year Automation Stop warranty on most products.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
GE Fanuc manufactured the IC200ERM002 unit as an expansion receiver module. This module is non-isolated and belongs to the VersaMax series of products. This expansion receiver module enhances VersaMax PLC / I/O terminals and has a wide range of capabilities while also increasing the total number of units that can be connected. The IC200ERM002 expansion receiver module can hold up to 7 racks with 8 modules individually per rack. It must be equipped with a power source in order to deliver electricity to all connected devices. When adding an additional power source or power-boosting carrier, be sure you attach it to the primary source of the power of the IC200ERM002 expansion receiver module. This device has three (3) built-in LED, or light emitting diode, indicators that reflect the device's functioning state. This module may function either as a solo-ended VersaMax I/O extension system or as a multi-rack VersaMax I/O expansion system. The overall length of the wire may not exceed 50 feet (15 meters) when the module is utilized in a multi-rack installation.
When using this IC200ERM002 non-isolated expansion receiver module in a single-ended system with just one additional expanding panel, the wire should not be longer than 3.3 feet (1 meter) in length. It has a data transmission rate of either 2.765 Megabytes per second (Mbps) or 5 Mbps, depending on the implementation. This device has a backplane current consumption rating of 70 milliamperes at an out voltage of 5 volts, as well as 20 milliamperes at an output voltage of 3.3 volts.
Question: Does Automation Stop offer repairs on the IC200ERM002?
Answer: Yes. We offer repairs for the IC200ERM002 and it comes with our 1 Year Automation Stop Warranty.
Question: What type of warranty comes with the Emerson - GE Fanuc and IC200ERM002?
Answer: If you buy the IC200ERM002 through Automationstop.com it comes with our 1 Year Warranty and no other warranties.
Question: Can I buy the IC200ERM002 online?
Answer: Yes. Automation Stop sells the IC200ERM002 online and you can check out for the quantity and condition listed available above.
Question: What is the manufacturer for the IC200ERM002?
Answer: The IC200ERM002 is made by Emerson - GE Fanuc.
For additional information about IC200ERM002 check the data sheet or manual. Also check the manual PDF for all wiring diagrams, compatibility, troubleshooting, specifications, installation instructions, and accessories (such as batteries, terminal blocks, or cables) regarding IC200ERM002.
Revision Part # | Also Known As | Availability |
---|---|---|
IC200ERM002A | IC200ERM002 Series A, Rev A | Request a Quote |
IC200ERM002C | IC200ERM002 Series C, Rev C | Request a Quote |
IC200ERM002E | IC200ERM002 Series E, Rev E | Request a Quote |
IC200ERM002G | IC200ERM002 Series G, Rev G | Request a Quote |
IC200ERM002J | IC200ERM002 Series J, Rev J | Request a Quote |
Common Misspellings:
Automation Stop sells used surplus products. Automation Stop is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by Automation Stop come with Automation Stop’s 1-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.