GE / IP FANUC Series 90/30 In Stock
Manufacturer: | Emerson - GE Fanuc |
Product Type: | Automation Product |
Part Number: | IC200CHS101 |
Series: | Versamax |
UPC: | 407257315442 |
Description:
Part number ICS200CHS101 is a disconnect-style interposing I/O terminal. The current rating is 0.5 amperes and has an alternating current and direct current voltage rating of 230 volts and 24 volts. respectively. The power supply rating is 220 volts AC (alternating current). This device features an RS-485 communication port and has sixteen (16) I/O points. Either one solid or stranded wire of specified dimensions can be accommodated in each terminal.
Automation Stop is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with Automation Stop's 1-year warranty.
We accept credit cards from all major providers, as well as PayPal.
We offer worldwide shipping with UPS and DHL.
We proudly offer a one year Automation Stop warranty on most products.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
The IC200CHS101 is a disconnect-style interposing I/O module that connects the VersaMax Connector-style I/O carrier and the field cables and provides a wholesome disconnection option for the VersaMax I/O module connected field devices. It is applicable with a lot of controllers such as the motion controller, the panel PCs, the programmable automation controller etc. The main base has an expansion connector which enables it to be connected to the interposing expansion base IC200CHS102. The main base, that is the IC200CHS101, is applicable with a VersaMax connector as it provides connections for the terminals on ‘A’ side of the VersaMax connector.
The device comes with a communication interface port RS-485 and has 16 I/O points. The alternating current power supply rating is 220 volts, the voltage supply for the direct current is 24 volts, whereas the voltage rating for the alternating current is 230 volts. The current rating is indicated as 0.5 amperes. The devices have a digital output type with a 7 segment Liquid crystal display whose advantage is that it can work under a wide range of temperatures, from a very hot condition to well below freezing temperatures.
For each terminal, the cross-sectional area that can be accommodated by the terminal is either 0.2 to 4.0 square millimeters one solid or 0.2 to 2.5 square millimeters stranded with a rated size of 12 to 24 American wire gauge. In case two wires are inserted in the same position, then the wires should be of the same type, either solid or stranded and should also be of the same size.
Question: Does Automation Stop offer repairs on the IC200CHS101?
Answer: Yes. We offer repairs for the IC200CHS101 and it comes with our 1 Year Automation Stop Warranty.
Question: What type of warranty comes with the Emerson - GE Fanuc and IC200CHS101?
Answer: If you buy the IC200CHS101 through Automationstop.com it comes with our 1 Year Warranty and no other warranties.
Question: Can I buy the IC200CHS101 online?
Answer: Yes. Automation Stop sells the IC200CHS101 online and you can check out for the quantity and condition listed available above.
Question: What is the manufacturer for the IC200CHS101?
Answer: The IC200CHS101 is made by Emerson - GE Fanuc.
For additional information about IC200CHS101 check the data sheet or manual. Also check the manual PDF for all wiring diagrams, compatibility, troubleshooting, specifications, installation instructions, and accessories (such as batteries, terminal blocks, or cables) regarding IC200CHS101.
Revision Part # | Also Known As | Availability |
---|---|---|
IC200CHS101A | IC200CHS101 Series A, Rev A | Request a Quote |
IC200CHS101C | IC200CHS101 Series C, Rev C | Request a Quote |
Common Misspellings:
Automation Stop sells used surplus products. Automation Stop is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by Automation Stop come with Automation Stop’s 1-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.