GE / IP FANUC Series 90/30 In Stock
Manufacturer: | Emerson - GE Fanuc |
Product Type: | Automation Product |
Part Number: | IC200UEX012 |
Series: | Versamax Micro |
UPC: | 865921450569 |
Description:
Part number IC200UEX012, which was designed and manufactured by Emerson - GE Fanuc, is a power supply module. This module belongs to the Series 90-30 product line. This module is equipped with eight (8) positive and negative logic inputs. These inputs operate at 24 volts DC. Additionally, this module has an output configuration consisting of six (6) normally open (NO) relay output circuits. This power supply module has an output power supply rating of 200 milliamperes at 24 volts DC.
Automation Stop is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with Automation Stop's 1-year warranty.
We accept credit cards from all major providers, as well as PayPal.
We offer worldwide shipping with UPS and DHL.
We proudly offer a one year Automation Stop warranty on most products.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
The IC200UEX012 is a power supply module. This module belongs to the Series 90-30 product line and is a part of the Versamax Micro series of products. Emerson - GE Fanuc designed and produced this module. This VersaMax power supply module features a speedy cycle time and simple programming and installation methods to help users get the most out of their time. It features eight (8) positive and negative logic inputs that operate at 24 volts DC. It is a high-definition power supply module that supports various automation products and is used in many applications such as processing, metal forming, and robotics.
On the other hand, this power supply unit supports the output configuration with six (6) normally open (NO) relay output circuits that draw up to 2 amperes of current. It also includes a 200-milliampere output power supply with a 24 volts DC rating for end systems and input circuits. Aside from that, the average current of this module is 7.5 milliamperes, when the on and off threshold voltage levels are 15 volts DC minimum. At 24 volts DC, the active current transducers level is -20% to +25%. Aside from that, this module has a ten (10) millisecond holdup time after a power outage at 19.2 volts DC and is rated for a 4 watts input power supply. At 30 volts DC, it has a 1 ampere inrush current rating. As a result, the amperage required to charge the capacitors is reduced, as is the current required to turn on the device.
Question: Does Automation Stop offer repairs on the IC200UEX012?
Answer: Yes. We offer repairs for the IC200UEX012 and it comes with our 1 Year Automation Stop Warranty.
Question: What type of warranty comes with the Emerson - GE Fanuc and IC200UEX012?
Answer: If you buy the IC200UEX012 through Automationstop.com it comes with our 1 Year Warranty and no other warranties.
Question: Can I buy the IC200UEX012 online?
Answer: Yes. Automation Stop sells the IC200UEX012 online and you can check out for the quantity and condition listed available above.
Question: What is the manufacturer for the IC200UEX012?
Answer: The IC200UEX012 is made by Emerson - GE Fanuc.
For additional information about IC200UEX012 check the data sheet or manual. Also check the manual PDF for all wiring diagrams, compatibility, troubleshooting, specifications, installation instructions, and accessories (such as batteries, terminal blocks, or cables) regarding IC200UEX012.
Revision Part # | Also Known As | Availability |
---|---|---|
IC200UEX012D | IC200UEX012 Series D, Rev D | Request a Quote |
Common Misspellings:
Automation Stop sells used surplus products. Automation Stop is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by Automation Stop come with Automation Stop’s 1-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.