GE / IP FANUC Series 90/30 In Stock
Manufacturer: | Emerson - GE Fanuc |
Product Type: | Automation Product |
Part Number: | IC697BEM713 |
Series: | Series 90-70 |
UPC: | 799705795143 |
Description:
The GE Fanuc IC697BEM713 bus transmitter module is a bus transmitter module. This connects expansion racks to the system. This module requires a 5-volt direct current supply with a 1.4-ampere current rating. This module is basic, straightforward to set up, and does not need the use of DIP switches. There are two (2) connectors on this GE module: one on top for interfacing and one on the bottom for daisy-chaining. It may only be mounted on the right side of any GE IC697-X interrupt source module.
Automation Stop is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with Automation Stop's 1-year warranty.
We accept credit cards from all major providers, as well as PayPal.
We offer worldwide shipping with UPS and DHL.
We proudly offer a one year Automation Stop warranty on most products.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
The GE Fanuc IC697BEM713 is a bus transmitter module. This establishes a connection with expansion racks. This module requires 5 volts direct current (DC) and a current rating of 1.4 amperes. This module is simple, easy to set up, and does not require DIP switches. It's from the Series 90-70 product line. This module can accommodate IC697 PLC racks and cater to expansion. Along with the many other advantages that this module provides, the parallel programming feature distinguishes it. This GE Fanuc module has two (2) connectors: one on top for interfacing and one on the bottom for daisy-chaining. The data rate of this GE Fanuc programmer interface is 500 kilobytes per second, and the cable's maximum length is 50 feet. MS-DOS or Windows programming software should be used for configuration. Status LEDs, or light emitting diodes, are present to alert you if there is a problem or error with any port or the entire system. There are three (3) main LEDs. The top LED indicates configuration completion, the middle LED indicates communication by blinking, and the last LED indicates the status of the expansion bus. Before installing modules, make sure that all of the instructions in the manual are followed and that the rack power is turned off. When the installation is finished, the power can be turned on. This prevents system damage and provides proper installation with accurate results. However, it should be noted that the module does not support installation in slot 1. It only supports installation at the right of any GE IC697-X interrupt source modules.
Question: Does Automation Stop offer repairs on the IC697BEM713?
Answer: Yes. We offer repairs for the IC697BEM713 and it comes with our 1 Year Automation Stop Warranty.
Question: What type of warranty comes with the Emerson - GE Fanuc and IC697BEM713?
Answer: If you buy the IC697BEM713 through Automationstop.com it comes with our 1 Year Warranty and no other warranties.
Question: Can I buy the IC697BEM713 online?
Answer: Yes. Automation Stop sells the IC697BEM713 online and you can check out for the quantity and condition listed available above.
Question: What is the manufacturer for the IC697BEM713?
Answer: The IC697BEM713 is made by Emerson - GE Fanuc.
For additional information about IC697BEM713 check the data sheet or manual. Also check the manual PDF for all wiring diagrams, compatibility, troubleshooting, specifications, installation instructions, and accessories (such as batteries, terminal blocks, or cables) regarding IC697BEM713.
Revision Part # | Also Known As | Availability |
---|---|---|
IC697BEM713B | IC697BEM713 Series B, Rev B | Request a Quote |
IC697BEM713E | IC697BEM713 Series E, Rev E | Request a Quote |
IC697BEM713F | IC697BEM713 Series F, Rev F | Request a Quote |
IC697BEM713G | IC697BEM713 Series G, Rev G | Request a Quote |
IC697BEM713H | IC697BEM713 Series H, Rev H | Request a Quote |
IC697BEM713J | IC697BEM713 Series J, Rev J | Request a Quote |
Common Misspellings:
Automation Stop sells used surplus products. Automation Stop is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by Automation Stop come with Automation Stop’s 1-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.