GE / IP FANUC Series 90/30 In Stock
Manufacturer: | Emerson - GE Fanuc |
Product Type: | Automation Product |
Part Number: | IC697ACC702 |
Series: | Series 90-70 |
Description:
The IC697ACC702 I/O Bus Terminator Plug is part of GE Fanuc's Series 90-70 family of PLCs (Programmable Logic Controllers). It features a 25-pin connection, is black in color, and weighs about 0.04 kg. This module’s bus terminator plug (connector) is normally included with every bus device and is not needed except for the chain's end bus receiver module. This I/O bus termination connector is designed for use with the GE Series 90-30 module and is needed for each local expansion pack.
Automation Stop is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with Automation Stop's 1-year warranty.
We accept credit cards from all major providers, as well as PayPal.
We offer worldwide shipping with UPS and DHL.
We proudly offer a one year Automation Stop warranty on most products.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
GE Fanuc manufactures the IC697ACC702 I/O Bus Terminator Plug, including the GE Series 90-70 PLC's bus receiver module. It is equipped with a 25-pin connection. This terminal plug is required for usage on the bus receivers at the daisy chain's end. It incorporates a termination system. This GE Bus terminator connector for the Series 90-70 is also suitable with the GE Series 90-30 components. This device weighs approximately 0.04 kg. This plug and module enable the easy integration of the I/O module and terminator block functionality into a single integrated system. The IC697ACC702 module I/O Bus Terminator Plug enables customers to benefit from the improved connection, increasing both flexibility, and cost savings within their networking applications.
This I/O Bus Terminator Plug can be placed in the receiver module's ‘’Expansion Port Out” port. When the device is bought, the kit includes all of the necessary screws for setup. This terminator connector enables its users to quickly and successfully terminate the I/O extension bus. To verify the terminator plug's presence and connection, users can utilize the processor's center LED incompatible modules. The GE Fanuc IC697ACC702 I/O Bus Terminator Plug is suitable for usage in both regular and standby PLC systems. This 25-pin connection may be used to link to the female connection situated on the CPU's base plate. It may be linked to an I/O bus extension chain if it is the chain's last cable. The manufacturer recommends using a resistor plug with the termination cords. Within the connection is a resistor pack.
Question: Does Automation Stop offer repairs on the IC697ACC702?
Answer: Yes. We offer repairs for the IC697ACC702 and it comes with our 1 Year Automation Stop Warranty.
Question: What type of warranty comes with the Emerson - GE Fanuc and IC697ACC702?
Answer: If you buy the IC697ACC702 through Automationstop.com it comes with our 1 Year Warranty and no other warranties.
Question: Can I buy the IC697ACC702 online?
Answer: Yes. Automation Stop sells the IC697ACC702 online and you can check out for the quantity and condition listed available above.
Question: What is the manufacturer for the IC697ACC702?
Answer: The IC697ACC702 is made by Emerson - GE Fanuc.
For additional information about IC697ACC702 check the data sheet or manual. Also check the manual PDF for all wiring diagrams, compatibility, troubleshooting, specifications, installation instructions, and accessories (such as batteries, terminal blocks, or cables) regarding IC697ACC702.
Revision Part # | Also Known As | Availability |
---|---|---|
IC697ACC702A | IC697ACC702 Series A, Rev A | Request a Quote |
Common Misspellings:
Automation Stop sells used surplus products. Automation Stop is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by Automation Stop come with Automation Stop’s 1-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.