GE / IP FANUC Series 90/30 In Stock
Manufacturer: | Emerson - GE Fanuc |
Product Type: | Automation Product |
Part Number: | IC694TBS132 |
Series: | RX3i PacSystem |
UPC: | 924471433146 |
Description:
GE Fanuc manufactures the IC694TBS132 extended spring-type terminal block module. It is equipped with 36 pins for connection purposes. The connecting wire strip in the block is 0.310 inches in full length. The 36 connector ports on this block are being used to connect the module to the field. This terminal block requires an open enclosure and must always be covered from spray nozzles of water.
Automation Stop is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with Automation Stop's 1-year warranty.
We accept credit cards from all major providers, as well as PayPal.
We offer worldwide shipping with UPS and DHL.
We proudly offer a one year Automation Stop warranty on most products.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
The IC694TBS132 terminal block by GE Fanuc is designed to work with a GE RX3i mid-range controller device in the RX3i PacSystem. For distributed I/O, the PacSystem includes an integrated PROFINET network. The terminal block is identical to the IC694TBB132 terminal block and has a longer spring. It's part of GE's RX3i range of industrial automation products. The block's exterior terminal cover is 13 millimeters deeper than conventional terminal block coverings. With wire gauges ranging from 14 to 28 AWG, this terminal block can readily accept bigger wires than the typical. The wire strip in the box is 0.310 inches long in total. This block's 36 connections are utilized for field wiring to the module. The open enclosure design of the IC694TBS132 terminal block should be secured against spray nozzles of water at all times. A terminal door protects the connections in the front area of the block. The field power should be entirely unplugged before installing a terminal block assembly. On top of the block’s terminal, the catalog number label must be put together with the module. During the installation procedure, the module wiring should be completed, and the wire bundles should be secured. Installing and using the IC694TBS132 terminal block is simple. Installing the terminal block is as simple as centering it and pressing it into position until it connects into place. The block's terminal front latch can then be depressed until the block reaches the top of the slot. The terminal block is tiny and compact, making it ideal for use on a small panel.
Question: Does Automation Stop offer repairs on the IC694TBS132?
Answer: Yes. We offer repairs for the IC694TBS132 and it comes with our 1 Year Automation Stop Warranty.
Question: What type of warranty comes with the Emerson - GE Fanuc and IC694TBS132?
Answer: If you buy the IC694TBS132 through Automationstop.com it comes with our 1 Year Warranty and no other warranties.
Question: Can I buy the IC694TBS132 online?
Answer: Yes. Automation Stop sells the IC694TBS132 online and you can check out for the quantity and condition listed available above.
Question: What is the manufacturer for the IC694TBS132?
Answer: The IC694TBS132 is made by Emerson - GE Fanuc.
For additional information about IC694TBS132 check the data sheet or manual. Also check the manual PDF for all wiring diagrams, compatibility, troubleshooting, specifications, installation instructions, and accessories (such as batteries, terminal blocks, or cables) regarding IC694TBS132.
Revision Part # | Also Known As | Availability |
---|---|---|
IC694TBS132E | IC694TBS132 Series E, Rev E | Request a Quote |
Common Misspellings:
Automation Stop sells used surplus products. Automation Stop is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by Automation Stop come with Automation Stop’s 1-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.