GE / IP FANUC Series 90/30 In Stock
Manufacturer: | Emerson - GE Fanuc |
Product Type: | Automation Product |
Part Number: | IC694MDR390 |
Series: | RX3i PacSystem |
Description:
The GE Fanuc IC694MDR390 is an Input/Output Module. It is designed, and manufactured for the RX3i PacSystem PLCs from GE Fanuc. There are a total of 8 individually isolated sinking/source inputs on this mixed I/O PacSystem module. Furthermore, it comes with 8 individually-isolated normally-open relay outputs. 6 Milliamps at 5.0 Volts DC is the Maximum Backplane Draw on this module.
Automation Stop is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with Automation Stop's 1-year warranty.
We accept credit cards from all major providers, as well as PayPal.
We offer worldwide shipping with UPS and DHL.
We proudly offer a one year Automation Stop warranty on most products.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
For operation, the GE Fanuc IC694MDR390 requires AC/DC power supply. 24.0 Volts DC is its nominal input rating. The isolation rating on this module is 500 Volts AC (RMS). 7.5 milliamperes are its nominal input current rating. 7.5 ms, or milliseconds, (on/off) are its input response time at maximum. This device has a rated output voltage range of five (5) volts DC (direct current) to thirty (30) volts direct current or five (5) volts alternating current (AC) to two hundred fifty (250) volts alternating current. Five hundred (500) volts AC (RMS) is used to isolate each individual output point. Ten (10.0) milliamperes are the minimum possible load for the output circuits on the GE Fanuc IC694MDR390. The maximum output rating on this Input/Output module is 2.0 Amperes. 5.0 Amperes is its maximum inrush current rating. Fifteen (15) milliseconds (ms) are its maximum on/off response time. The GE Fanuc IC694MDR390 is meant to be used with the RX3i PacSystems PLC I/O. However, it does not support hot insertion or hot removal. It comes equipped with 16 front-panel LEDs. It is further divided into 2 groups with 4 outputs each. The LED Indicators on the GE Fanuc IC694MDR390 display the status of each of the connected I/O points.
The IC694MDR390 Input/Output Module comes with both communication and microprocessor capabilities. Without having to constantly communicate with the PLC’s CPU, it can keep count of the control outputs. For ease of use, it comes equipped with a hand-held monitor. The monitor displays data, such as preload, strobe, count, and other operational data. A 0 to 30 volts DC, or 115 volts AC, voltage rating is required for the high-speed counter block.
Question: Does Automation Stop offer repairs on the IC694MDR390?
Answer: Yes. We offer repairs for the IC694MDR390 and it comes with our 1 Year Automation Stop Warranty.
Question: What type of warranty comes with the Emerson - GE Fanuc and IC694MDR390?
Answer: If you buy the IC694MDR390 through Automationstop.com it comes with our 1 Year Warranty and no other warranties.
Question: Can I buy the IC694MDR390 online?
Answer: Yes. Automation Stop sells the IC694MDR390 online and you can check out for the quantity and condition listed available above.
Question: What is the manufacturer for the IC694MDR390?
Answer: The IC694MDR390 is made by Emerson - GE Fanuc.
For additional information about IC694MDR390 check the data sheet or manual. Also check the manual PDF for all wiring diagrams, compatibility, troubleshooting, specifications, installation instructions, and accessories (such as batteries, terminal blocks, or cables) regarding IC694MDR390.
Revision Part # | Also Known As | Availability |
---|---|---|
IC694MDR390C | IC694MDR390 Series C, Rev C | Request a Quote |
IC694MDR390D | IC694MDR390 Series D, Rev D | Request a Quote |
Common Misspellings:
Automation Stop sells used surplus products. Automation Stop is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by Automation Stop come with Automation Stop’s 1-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.