GE / IP FANUC Series 90/30 In Stock
Manufacturer: | Emerson - GE Fanuc |
Product Type: | Automation Product |
Part Number: | IC694ALG233 |
Series: | RX3i PacSystem |
Description:
This advanced analog current input module features 8 differential input channels as well as 16 single-ended input channels. it is a part of the RX3i PacSystem series of products by Emerson - GE Fanuc. IC694ALG233 has 16-bit resolution, as well as current ranges consisting of 4 to 20 milliamperes and 0 to 20 milliamperes. Other handy features include configurable scaling and offsets, as well as fault reporting. This device requires an external power source of 24 volts DC. It has a rated current consumption of 120 milliamperes at 5 volts DC. The IC694ALG233 can be mounted via a panel or a DIN rail.
Key Features:
Automation Stop is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with Automation Stop's 1-year warranty.
We accept credit cards from all major providers, as well as PayPal.
We offer worldwide shipping with UPS and DHL.
We proudly offer a one year Automation Stop warranty on most products.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
The IC694ALG233 is a 16 single-ended input channel RX3i PacSystem analog current input module. Three (3) input ranges are changeable using configuration software for each input: 4 to 20 milliamperes, 0 to 20 milliamperes, and 4 to 20 milliamperes enhanced are the three different current ranges.
Additionally, via its allocated program reference addresses, part number IC694ALG233 transmits the status of the module and the power supply to the CPU (central processing unit). In an RX3i system, the IC694ALG233 must be inserted in an I/O slot with a serial connector. There are no module jumpers to set on the IC694ALG233 module because it is configured using software. In the four (4) to twenty (20) milliamperes Enhanced Range, open-circuit detection is offered for all inputs. The state of the module can be easily determined by looking at the LEDs (light emitting diodes) that are emitted. ON indicates that everything is in order and that the module is properly configured. If the LED continues to blink rapidly, there is a problem with the setup data. A failed power-up diagnostics issue or a code execution error is indicated by slow blinking followed by OFF. OFF indicates that there is no power to the backplane, or that the program is not operating.
In the logic program, this module provides diagnostic point fault contacts, as well as firmware upgrades. Positive and negative rate of change alerts are featured, as well as a display of the module serial number, revision, and date code. Hot insertion/removal is also possible with this module.
Question: Does Automation Stop offer repairs on the IC694ALG233?
Answer: Yes. We offer repairs for the IC694ALG233 and it comes with our 1 Year Automation Stop Warranty.
Question: What type of warranty comes with the Emerson - GE Fanuc and IC694ALG233?
Answer: If you buy the IC694ALG233 through Automationstop.com it comes with our 1 Year Warranty and no other warranties.
Question: Can I buy the IC694ALG233 online?
Answer: Yes. Automation Stop sells the IC694ALG233 online and you can check out for the quantity and condition listed available above.
Question: What is the manufacturer for the IC694ALG233?
Answer: The IC694ALG233 is made by Emerson - GE Fanuc.
For additional information about IC694ALG233 check the data sheet or manual. Also check the manual PDF for all wiring diagrams, compatibility, troubleshooting, specifications, installation instructions, and accessories (such as batteries, terminal blocks, or cables) regarding IC694ALG233.
Revision Part # | Also Known As | Availability |
---|---|---|
IC694ALG233-BB | IC694ALG233 Series BB, Rev BB | Request a Quote |
IC694ALG233-ED | IC694ALG233 Series ED, Rev ED | Request a Quote |
IC694ALG233-GD | IC694ALG233 Series GD, Rev GD | Request a Quote |
Common Misspellings:
Automation Stop sells used surplus products. Automation Stop is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by Automation Stop come with Automation Stop’s 1-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.