GE / IP FANUC Series 90/30 In Stock
Manufacturer: | Emerson - GE Fanuc |
Product Type: | Automation Product |
Part Number: | ST-3218 |
Series: | RSTi PacSystem |
UPC: | 799705804722 |
Description:
Product number ST-3218 is an RSTi PacSystem analog input module. This module, which was designed and manufactured by Emerson - GE Fanuc, has 8 channels. This device has an input range of 4 to 20 milliamperes. It has 12-bit resolution. The input impedance of this module is rated at 120 ohms. The module current consumption is 60 milliamperes at 5 volts DC. The operating temperature range for this module is 0 to 60 degrees Celsius.
Automation Stop is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with Automation Stop's 1-year warranty.
We accept credit cards from all major providers, as well as PayPal.
We offer worldwide shipping with UPS and DHL.
We proudly offer a one year Automation Stop warranty on most products.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
The ST-3218 is an RSTi PacSystem analog input module. This module was designed and manufactured by Emerson - GE Fanuc. This device consists of eight (8) channels. It has a current input that is indicated to range from 4 milliamperes to 20 milliamperes. The GE Fanuc ST-3218 is classified as a current analog input module. It has a 12-bit resolution and is equipped with a terminal block connector. This device has no common terminal within the module and, therefore, a field power rated at 0 volts is common.
The ST-3218 analog input module has an accuracy rated at plus or minus (+/-) 0.1 percent full scale at 25 degrees Celsius (°C), as well as plus or minus (+/-) 0.3 percent full scale at 0 degrees Celsius (°C) and 60 degrees Celsius (°C). This analog input module has an input impedance rated at 120 ohms. The update time of the GE Fanuc ST-3218 is 4 milliseconds for all of the channels. Additionally, the module current consumption of this device is 50 milliamperes at 5 volts direct current (DC). This analog input module uses photo coupler isolation. This device has an approximate weight of 0.07 kilograms. Additionally, the physical dimensions of this analog input module measure 1.2 centimeters x 9.9 centimeters x 7.0 centimeters. The temperature of the area surrounding this module should range from 0 to 60 degrees Celsius when in operation. When being stored, however, the temperature of the surrounding area should range from -40 to 85 degrees Celsius. The relative humidity should have levels that range from 5% to 95% and be non-condensing.
Question: Does Automation Stop offer repairs on the ST-3218?
Answer: Yes. We offer repairs for the ST-3218 and it comes with our 1 Year Automation Stop Warranty.
Question: What type of warranty comes with the Emerson - GE Fanuc and ST-3218?
Answer: If you buy the ST-3218 through Automationstop.com it comes with our 1 Year Warranty and no other warranties.
Question: Can I buy the ST-3218 online?
Answer: Yes. Automation Stop sells the ST-3218 online and you can check out for the quantity and condition listed available above.
Question: What is the manufacturer for the ST-3218?
Answer: The ST-3218 is made by Emerson - GE Fanuc.
For additional information about ST-3218 check the data sheet or manual. Also check the manual PDF for all wiring diagrams, compatibility, troubleshooting, specifications, installation instructions, and accessories (such as batteries, terminal blocks, or cables) regarding ST-3218.
Revision Part # | Also Known As | Availability |
---|---|---|
ST-3218-BA | ST-3218 Series BA, Rev BA | Request a Quote |
Common Misspellings:
Automation Stop sells used surplus products. Automation Stop is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by Automation Stop come with Automation Stop’s 1-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.