GE / IP FANUC Series 90/30 In Stock
Manufacturer: | Emerson - GE Fanuc |
Product Type: | Automation Product |
Part Number: | ST-3134 |
Series: | RSTi PacSystem |
UPC: | 799705804708 |
Description:
The Emerson - GE Fanuc ST-3134 GE ST3134 is an additional analog input module that has 4 single-ended input channels. These inputs are non-isolated between the channels. The input current ranges from 0 to 20 mA and the power supply is a DC to DC system. this device has a maximum power dissipation of 165 mA at 5.0 volts. The module has an impedance rating of 120 ohms and a conversion time of 4 milliseconds.
Automation Stop is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with Automation Stop's 1-year warranty.
We accept credit cards from all major providers, as well as PayPal.
We offer worldwide shipping with UPS and DHL.
We proudly offer a one year Automation Stop warranty on most products.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
The ST-3134, which was designed and manufactured by Emerson - GE Fanuc, is an additional RSTi analog input module. This module has 4 single-ended channels of analog inputs and an input current that ranges from 0 to 20 milliamperes. It has a resolution of 14 bits that has a range of14 bits : 1.22 uA/Bit. There are 5 indicators on the module and 4 of them are just a Green/Red status indicator. The remaining indicator is for the Green/Red Fn-BUS state. The data is formatted in a 16 bit integer format with a 2’s complement. There is a +/- 0.1% full scale error possible at the temperature of 25°C and an error of +/- 0.3% is possible at 0° or 60°C (full scale). The input impedance rating of this device is 120 ohms. There is no calibration requirement for this module and the conversion time is 4 milliseconds. The common type for this device is 4 channels of 2COM (single common). The power supply is a simple system power DC/DC. The maximum power dissipation rating of this device is 165 milliamperes at five (5) volts DC (direct current). From the I/O of the module to the Logic, there is an optocoupler isolation. The I/O cable extends to be a 2.0-meter wire. There are eight (8) pins on the module. For pins 0 to 3, there are four (4) input channels. For the pin numbers 4 and 5, they both are the input channel common with 0 volts. Pins 6 and 7 are the chassis ground /shield. This module has an approximate weight of 70 grams. The physical dimensions of this device measure 12 mm 99 mm x 70 mm.
Question: Does Automation Stop offer repairs on the ST-3134?
Answer: Yes. We offer repairs for the ST-3134 and it comes with our 1 Year Automation Stop Warranty.
Question: What type of warranty comes with the Emerson - GE Fanuc and ST-3134?
Answer: If you buy the ST-3134 through Automationstop.com it comes with our 1 Year Warranty and no other warranties.
Question: Can I buy the ST-3134 online?
Answer: Yes. Automation Stop sells the ST-3134 online and you can check out for the quantity and condition listed available above.
Question: What is the manufacturer for the ST-3134?
Answer: The ST-3134 is made by Emerson - GE Fanuc.
For additional information about ST-3134 check the data sheet or manual. Also check the manual PDF for all wiring diagrams, compatibility, troubleshooting, specifications, installation instructions, and accessories (such as batteries, terminal blocks, or cables) regarding ST-3134.
Revision Part # | Also Known As | Availability |
---|---|---|
ST-3134-BA | ST-3134 Series BA, Rev BA | Request a Quote |
Common Misspellings:
Automation Stop sells used surplus products. Automation Stop is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by Automation Stop come with Automation Stop’s 1-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.