GE / IP FANUC Series 90/30 In Stock
Manufacturer: | Emerson - GE Fanuc |
Product Type: | Automation Product |
Part Number: | IC660BCM501 |
Series: | Genius I/O |
UPC: | 900201889247 |
Description:
Designed and manufactured by Emerson - GE Fanuc, part number IC660BCM501 is a battery charger module for handheld portable monitor modules. It belongs to the Genius I/O series of products. This device operates via a built-in battery or a power source with a voltage rating of 115/230 volts AC. This GE Fanuc module has an approximate weight of three (3) pounds. Users should not rely consistently on the AC power source as it may cause poor performance in this module.
Automation Stop is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with Automation Stop's 1-year warranty.
We accept credit cards from all major providers, as well as PayPal.
We offer worldwide shipping with UPS and DHL.
We proudly offer a one year Automation Stop warranty on most products.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
The IC660BCM501 is a portable monitor battery charger module from the Genius I/O family, manufactured by GE Fanuc. The primary application of this battery is to charge a GE Fanuc handheld portable monitor module. This battery module has an approximate weight of three (3) pounds. This module can be operated either by a built-in battery or by a 115-volt or 230-volt AC power source. Even when using AC (alternating current) power, the battery pack must be installed to continue working this unit. This unit can supply the power directly to the handled monitor from its internal battery directly, or users can also use the external AC power supply source.
After two years of AC operation, the battery pack may not be able to hold sufficient charge for the unit to operate independently. Therefore, if you are using a fresh battery to power the monitor or it is already overused, it is suggested to charge the battery for at least fifteen (15) minutes before using the monitor, which is considered a best practice to boost the health of the battery. The fast-charging cable should be plugged into the system, and the battery must be charged for fifteen (15) minutes before powering it on. In addition, it may be necessary to remove and reinstall the battery for fifteen (15) to twenty (20) seconds. Aside from that, users should also avoid consistently relying on the AC power source as it may cause the battery to drain, which might eventually result in poor performance.
Question: Does Automation Stop offer repairs on the IC660BCM501?
Answer: Yes. We offer repairs for the IC660BCM501 and it comes with our 1 Year Automation Stop Warranty.
Question: What type of warranty comes with the Emerson - GE Fanuc and IC660BCM501?
Answer: If you buy the IC660BCM501 through Automationstop.com it comes with our 1 Year Warranty and no other warranties.
Question: Can I buy the IC660BCM501 online?
Answer: Yes. Automation Stop sells the IC660BCM501 online and you can check out for the quantity and condition listed available above.
Question: What is the manufacturer for the IC660BCM501?
Answer: The IC660BCM501 is made by Emerson - GE Fanuc.
For additional information about IC660BCM501 check the data sheet or manual. Also check the manual PDF for all wiring diagrams, compatibility, troubleshooting, specifications, installation instructions, and accessories (such as batteries, terminal blocks, or cables) regarding IC660BCM501.
Revision Part # | Also Known As | Availability |
---|
Common Misspellings:
Automation Stop sells used surplus products. Automation Stop is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by Automation Stop come with Automation Stop’s 1-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.