GE / IP FANUC Series 90/30 In Stock
Manufacturer: | Emerson - GE Fanuc |
Product Type: | Automation Product |
Part Number: | IC660BBD100 |
Series: | Genius I/O |
UPC: | 816282144567 |
Description:
The IC660BBD100 is an 8-Circuit Grouped I/O Block, 115 VAC made by GE Fanuc, and belongs to the GE Automation Intelligent Platform Series. The IC660BBD100 is made up of eight discrete circuits that are integrated with a single group and operate at 115 volts AC. Each separate circuit may operate as an input, a tri-state input, or an output. This device does not need a special power source since the power controller tapers off from the input/output device voltages connected to the IC660BBD100 block's terminals.
Key Features:
Automation Stop is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with Automation Stop's 1-year warranty.
We accept credit cards from all major providers, as well as PayPal.
We offer worldwide shipping with UPS and DHL.
We proudly offer a one year Automation Stop warranty on most products.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
The IC660BBD100 I/O block is rated for 115 Volts Alternate Current. It's a circuit I/O block with one set of eight circuits made by GE Fanuc. The block's circuits can be used as inputs, outputs, or tristate inputs. It is manufactured by GE Fanuc Automation and is utilized in many industrial and manufacturing industries. The block's operating frequency is 50 to 60 Hertz. This I/O block has 8 inputs and may be linked to a programmer, controller, or monitoring device through the connector on the top of the block to monitor various configurations. Ports 1 and 2 of the serial controllers are also available on the block. The IC660BBD100 I/O block is compatible with the GE PLC systems Series 90-30 and Series 90-70. It is possible to connect the block to a computer and configure it using the Window Windows XP operating system by Microsoft.
On the front side of the IC660BBD100 by GE Fanuc I/O block there are several LED indicators. When an application is running, an "I/O Enabled" LED glows, and a "Unit OK" LED illuminates. Selectable thresholds and sophisticated diagnostics are among the I/O block's unique characteristics. The block's input to the grounding or serial bus isolation is 1500 volts. When connected to 16 inputs at a full load, the IC660BBD100 I/O block can discharge 28 Watts of maximum heat. The terminal board of the block has a current rating of 5 amps. For proper operation, the temperature should be set from 0 to 60 ° C.
Question: Does Automation Stop offer repairs on the IC660BBD100?
Answer: Yes. We offer repairs for the IC660BBD100 and it comes with our 1 Year Automation Stop Warranty.
Question: What type of warranty comes with the Emerson - GE Fanuc and IC660BBD100?
Answer: If you buy the IC660BBD100 through Automationstop.com it comes with our 1 Year Warranty and no other warranties.
Question: Can I buy the IC660BBD100 online?
Answer: Yes. Automation Stop sells the IC660BBD100 online and you can check out for the quantity and condition listed available above.
Question: What is the manufacturer for the IC660BBD100?
Answer: The IC660BBD100 is made by Emerson - GE Fanuc.
For additional information about IC660BBD100 check the data sheet or manual. Also check the manual PDF for all wiring diagrams, compatibility, troubleshooting, specifications, installation instructions, and accessories (such as batteries, terminal blocks, or cables) regarding IC660BBD100.
Revision Part # | Also Known As | Availability |
---|---|---|
IC660BBD100A | IC660BBD100 Series A, Rev A | Request a Quote |
IC660BBD100B | IC660BBD100 Series B, Rev B | Request a Quote |
IC660BBD100-BA | IC660BBD100 Series BA, Rev BA | Request a Quote |
Common Misspellings:
Automation Stop sells used surplus products. Automation Stop is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by Automation Stop come with Automation Stop’s 1-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.