GE / IP FANUC Series 90/30 In Stock
Manufacturer: | Emerson - GE Fanuc |
Product Type: | Automation Product |
Part Number: | IC600PM502 |
Series: | Series Six |
UPC: | 824005297643 |
Description:
Designed and produced by the company known as Emerson - GE Fanuc, product number IC600PM502 is a standard I/O power supply module for Series Six PLCs. This module has a voltage range of 115 to 230 volts alternating current (AC). This device has a standard capacity rated at 5 volts direct current (DC). It also has a maximum current rating of 6.1 amperes. This module should be used indoors and should be stored in a clean environment.
Automation Stop is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with Automation Stop's 1-year warranty.
We accept credit cards from all major providers, as well as PayPal.
We offer worldwide shipping with UPS and DHL.
We proudly offer a one year Automation Stop warranty on most products.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
This power supply, the IC600PM502, was created and designed by GE Fanuc as a standard power supply. This device's voltage range is between one hundred and fifteen (115) and two hundred and thirty (230) volts alternating current (AC). This power supply supplies electricity to the GE Fanuc Series Six line of Input / Output modules. Aside from that, this open enclosure power supply provides electricity to a module via the backplane. The power supply's front panel contains an on/off switch that may be used to control the power flow in the module. Along with the switch, there is an LED indicator that lights when the switch is switched on. This GE Fanuc power supply module has a standard capacity of five (5) volts direct current (DC) and a maximum current rating of six-point-one (6.1) amperes. The input power of this device is sent to the terminal block on the bottom of the power unit. On the circuit board of the IC600PM502 power supply are direct current (DC) output terminals, a power failure signal terminal, and ground connections. The terminal block that connects power to the module is located on the module's front side. In the power rack, a power switch/circuit breaker protects the power supply from unfavorable current and voltage circumstances. The load of the device should be determined during the installation of the power supply to avoid overload circumstances. A jumper on the terminal block must be used to set the input voltage mode. This device is meant for indoor use and should be stored in a clean environment.
Question: Does Automation Stop offer repairs on the IC600PM502?
Answer: Yes. We offer repairs for the IC600PM502 and it comes with our 1 Year Automation Stop Warranty.
Question: What type of warranty comes with the Emerson - GE Fanuc and IC600PM502?
Answer: If you buy the IC600PM502 through Automationstop.com it comes with our 1 Year Warranty and no other warranties.
Question: Can I buy the IC600PM502 online?
Answer: Yes. Automation Stop sells the IC600PM502 online and you can check out for the quantity and condition listed available above.
Question: What is the manufacturer for the IC600PM502?
Answer: The IC600PM502 is made by Emerson - GE Fanuc.
Question: What VAC (voltage alternating current) is included with the IC600PM502?
Answer: The IC600PM502 has a VAC (voltage alternating current) of 115-230.
For additional information about IC600PM502 check the data sheet or manual. Also check the manual PDF for all wiring diagrams, compatibility, troubleshooting, specifications, installation instructions, and accessories (such as batteries, terminal blocks, or cables) regarding IC600PM502.
Revision Part # | Also Known As | Availability |
---|---|---|
IC600PM502A | IC600PM502 Series A, Rev A | Request a Quote |
IC600PM502K | IC600PM502 Series K, Rev K | Request a Quote |
Common Misspellings:
Automation Stop sells used surplus products. Automation Stop is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by Automation Stop come with Automation Stop’s 1-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.