GE / IP FANUC Series 90/30 In Stock
Manufacturer: | Emerson - GE Fanuc |
Product Type: | Automation Product |
Part Number: | IC600CB524 |
Series: | Series Six |
UPC: | 498924230175 |
Description:
Part number IC600CB524, which was designed and manufactured by Emerson - GE Fanuc, is an arithmetic control module. The circuit board has dimensions that measure 8.15 inches x 11.0 inches, while the faceplate has physical dimensions that measure 12.46 inches x 1.175 inches. The required power to operate this device is supplied from the CPU. This power is rated at 5 volts DC with a current rating of 1.7 amperes. The operating temperature for this module should range from 0 to 60 degrees Celsius.
Automation Stop is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with Automation Stop's 1-year warranty.
We accept credit cards from all major providers, as well as PayPal.
We offer worldwide shipping with UPS and DHL.
We proudly offer a one year Automation Stop warranty on most products.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
The IC600CB524 is an arithmetic control module used for performing logical and arithmetic functions of a Series Six or Model 60, 600, and 6000 central processing unit (CPU). The module has four (4) integrated circuits of with a 16-bit microprocessor. The circuits that are integrated into the module work together with the logic control module to produce timing signals and system control. A ribbon cable connector is used to link the arithmetic control module to the logic control module. It is important to note that any attempt to link the two modules, the control and logic modules, without the use of the ribbon cable will lead to unpredictable operation of the central processing unit.
The circuit board dimensions are given as 8.15 inches by 11.0 inches, whereas the faceplate dimensions are estimated to be 12.46 inches by 1.175 inches. The power required for operation is supplied by the central processing unit's power supply and is given as 5 volts direct current (DC) with a current rating of 1.7 amperes. The temperatures suitable for exposure during operations ranges from 0 to 60 degrees Celsius, and the module can be stored in temperatures that range from -20 to 70 degrees Celsius. The relative humidity should be maintained at 5 percent to 95 percent and should be non-condensing.
The faceplate has lenses through which two LED indicators are visible. The primary purpose of these LEDs is to indicate fault that may be present in the central processing unit. The one with the CHECK label remains lit as a sign that self-diagnosis is complete. The other LED, which is labeled RUN, is to show that the central processing unit is in run mode.
Question: Does Automation Stop offer repairs on the IC600CB524?
Answer: Yes. We offer repairs for the IC600CB524 and it comes with our 1 Year Automation Stop Warranty.
Question: What type of warranty comes with the Emerson - GE Fanuc and IC600CB524?
Answer: If you buy the IC600CB524 through Automationstop.com it comes with our 1 Year Warranty and no other warranties.
Question: Can I buy the IC600CB524 online?
Answer: Yes. Automation Stop sells the IC600CB524 online and you can check out for the quantity and condition listed available above.
Question: What is the manufacturer for the IC600CB524?
Answer: The IC600CB524 is made by Emerson - GE Fanuc.
For additional information about IC600CB524 check the data sheet or manual. Also check the manual PDF for all wiring diagrams, compatibility, troubleshooting, specifications, installation instructions, and accessories (such as batteries, terminal blocks, or cables) regarding IC600CB524.
Revision Part # | Also Known As | Availability |
---|---|---|
IC600CB524K | IC600CB524 Series K, Rev K | Request a Quote |
IC600CB524M | IC600CB524 Series M, Rev M | Request a Quote |
Common Misspellings:
Automation Stop sells used surplus products. Automation Stop is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by Automation Stop come with Automation Stop’s 1-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.