GE / IP FANUC Series 90/30 In Stock
Manufacturer: | Emerson - GE Fanuc |
Product Type: | Automation Product |
Part Number: | IC610MDL179 |
Series: | Series One |
UPC: | 375139668293 |
Description:
The Ge Fanuc IC610MDL179 is an output module. It has 8 output circuits point categorized into two groups. Its control circuit voltage range is 115 Volts AC or 230 Volts AC, and its operating voltage is 80 -264 Volts AC at the AC frequency range of 47-63 Hz. Its minimum output current rating is 0.5A, and the max is 1A. These current ratings per output are variable depending on the operating temperatures, with the minimum being 20 degrees Celcius while the max being 60 degrees Celcius.
Automation Stop is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with Automation Stop's 1-year warranty.
We accept credit cards from all major providers, as well as PayPal.
We offer worldwide shipping with UPS and DHL.
We proudly offer a one year Automation Stop warranty on most products.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
It is an output module that comes with a flexible terminal board. This product is assembled by GE Fanuc. The voltage rating of this module is 115 or 230 volts AC. has eight circuits, which are used for output points. Like all the other efficient I/O modules, this module has a secure interface method. Some of the most typical applications that this module can provide robust interface are as follows: solenoid valves, motor contactors (NEMA), relay modules, and coils. Like the other output modules, it divides its output points into two groups of four. These same groupings can draw power from a variety of sources.
The Field systems, in particular, should always be powered by user-supplied sources. Aside from that, the ambient temperature determines the peak current output. At 20 ° C, each of the 8 outputs, for example, can generate 0.5 amps of current. At 60 ° Celsius, six output circuits can generate 1 amp of current. It runs on an AC voltage range of 80 to 264 volts. It has an AC frequency range of 47 to 63 Hz and a max current of 1A per output point. At 230 Volts and 60 Hz, its max leakage current is 1.2mA, and its rated on-state voltage drop is 1.5 Volts at 1A. It has a 1 ms off to on time delay rating for the module outputs and a 9 ms off to on time delay rating for the module inputs. A logic side circuit indication is also available on this unit. A single fuse rated at 5A is also internally available for each output group.
Question: Does Automation Stop offer repairs on the IC610MDL179?
Answer: Yes. We offer repairs for the IC610MDL179 and it comes with our 1 Year Automation Stop Warranty.
Question: What type of warranty comes with the Emerson - GE Fanuc and IC610MDL179?
Answer: If you buy the IC610MDL179 through Automationstop.com it comes with our 1 Year Warranty and no other warranties.
Question: Can I buy the IC610MDL179 online?
Answer: Yes. Automation Stop sells the IC610MDL179 online and you can check out for the quantity and condition listed available above.
Question: What is the manufacturer for the IC610MDL179?
Answer: The IC610MDL179 is made by Emerson - GE Fanuc.
Question: What VAC (voltage alternating current) is included with the IC610MDL179?
Answer: The IC610MDL179 by Emerson - GE Fanuc has a voltage alternating current (VAC) of 115-230.
For additional information about IC610MDL179 check the data sheet or manual. Also check the manual PDF for all wiring diagrams, compatibility, troubleshooting, specifications, installation instructions, and accessories (such as batteries, terminal blocks, or cables) regarding IC610MDL179.
Revision Part # | Also Known As | Availability |
---|---|---|
IC610MDL179A | IC610MDL179 Series A, Rev A | Request a Quote |
Common Misspellings:
Automation Stop sells used surplus products. Automation Stop is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by Automation Stop come with Automation Stop’s 1-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.