GE / IP FANUC Series 90/30 In Stock
Manufacturer: | Emerson - GE Fanuc |
Product Type: | Automation Product |
Part Number: | IC610MDL112 |
Series: | Series One |
UPC: | 122668148013 |
Description:
The IC610MDL112, which was manufactured by GE FANUC, is an input module. They can interact with 24-volt alternating current (AC) signals, as well as 24-volt direct current (DC) source-type signals. This module includes 16 input circuits, each with an LED indication, that are each intended to receive a single discrete (ON/OFF) signal from a user-supplied device or devices connected to the module. Pushbuttons, limit switches, selection switches, and relay contacts are all examples of input devices that are often used.
Automation Stop is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with Automation Stop's 1-year warranty.
We accept credit cards from all major providers, as well as PayPal.
We offer worldwide shipping with UPS and DHL.
We proudly offer a one year Automation Stop warranty on most products.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
The IC610MDL112 is a 24-volt direct current input module with a detachable terminal block. GE Fanuc produced this module. It contains sixteen isolated input points, each of which is isolated and is separated into two groups of eight points each. Located on the front of the device are LED indications to indicate whether an input point is connected and operational or not. The terminal unit is designed to receive discrete input data from user-input devices and to process them in order to be sent to the PLC-based operational system. It is compatible with a variety of switches, buttons, and sensing devices. The IC610MDL112 input unit is capable of communicating with input devices that generate their own voltages. Additionally, this input module may be utilized as a sink input device. Operators can power the module separately in sink mode.
The IC610MDL112 input device is linked to the user input devices through the screw terminal on the module's front side. These terminals take a single wire with a diameter of 12 AWG or two wires with a diameter of 14 AWG. The wire markers should be put at a lower limit of 88 inches from the terminating end to provide enough space for the hinged door that opens and close. The IC610MDL112 input module takes a current drawing of 0.25 amps from the 5 volts DC backplane source in general. The module includes a filter with a 20-millisecond delay. Installing and removing the input module is simple. The clamps on the rear of the cover secure it to a rack. For installation and replacement, the module may be slid onto the rail. The module is lightweight and small in size.
Question: Does Automation Stop offer repairs on the IC610MDL112?
Answer: Yes. We offer repairs for the IC610MDL112 and it comes with our 1 Year Automation Stop Warranty.
Question: What type of warranty comes with the Emerson - GE Fanuc and IC610MDL112?
Answer: If you buy the IC610MDL112 through Automationstop.com it comes with our 1 Year Warranty and no other warranties.
Question: Can I buy the IC610MDL112 online?
Answer: Yes. Automation Stop sells the IC610MDL112 online and you can check out for the quantity and condition listed available above.
Question: What is the manufacturer for the IC610MDL112?
Answer: The IC610MDL112 is made by Emerson - GE Fanuc.
For additional information about IC610MDL112 check the data sheet or manual. Also check the manual PDF for all wiring diagrams, compatibility, troubleshooting, specifications, installation instructions, and accessories (such as batteries, terminal blocks, or cables) regarding IC610MDL112.
Revision Part # | Also Known As | Availability |
---|---|---|
IC610MDL112A | IC610MDL112 Series A, Rev A | Request a Quote |
Common Misspellings:
Automation Stop sells used surplus products. Automation Stop is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by Automation Stop come with Automation Stop’s 1-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.