GE / IP FANUC Series 90/30 In Stock
| Manufacturer: | Emerson - GE Fanuc |
| Product Type: | Automation Product |
| Part Number: | IC697MDL940 |
| Series: | Series 90-70 |
| UPC: | 806244553285 |
Description:
The GE Fanuc Emerson IC697MDL940 is an output relay module that includes sixteen output points that deliver a voltage of either 120 volts AC to 240 volts AC or 5 volts DC, 24 volts DC or 125 volts DC. The module contains eight individually well-isolated Form C outputs and two groups of four Form A outputs. These outputs are labeled with green LED indicators to show the on/off status of outputs. The IC697MDL940 weighs approximately 860 grams (1.9 pounds) while shipping.
Automation Stop is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with Automation Stop's 1-year warranty.
Pay
We accept credit cards from all major providers, as well as PayPal.
Ship
We offer worldwide shipping with UPS and DHL.
Warranty
We proudly offer a one year Automation Stop warranty on most products.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
The GE Fanuc Emerson IC697MDL940 is an output relay module that includes sixteen output points that deliver a voltage of either 120 volts AC to 240 volts AC at a frequency range from 47 hertz to 63 hertz or 5 volts DC, 24 volts DC or 125 volts DC. The module contains eight individually well-isolated Form C outputs and two groups of four Form A outputs. These outputs are labeled with green LED indicators to show the on/off status of outputs. This module employs the backplane optical isolation offered by optocouplers to provide electrical isolation of 500 volts AC continuously between Form C outputs or Form A groups and 1500 volts AC between outputs and the backplane. The IC697MDL940 can be easily mounted in any input or output slots of the Field Control system. The output module provides an on response time of 10 milliseconds and an off response time of 10 milliseconds. The module has another LED indicator labeled “FUSE OK” that indicates the fuse state of outputs that are protected with 3 amperes fuses.
The IC697MDL940 draws a current of 750 milliamperes at a backplane voltage of 5 volts DC. The module outputs deliver a current of 100 milliamperes to 2 amperes per point for resistive loads and from 50 milliamperes to 1 ampere for inductive loads. This device can be employed with Series 90-70 PLCs for incandescent and inductive loads. The module has an RC snubber protection circuit that includes a resistor of 47 ohms and a capacitor of 15 nanofarads. This output module doesn’t require DIP switches or jumpers to be programmed and configured. This device can be programmed and configured with either MS-DOS or Windows through either the Ethernet TCP/IP or the SNP port. The IC697MDL940 weighs approximately 860 grams (1.9 pounds) while shipping and operates at 0 degrees to 60 degrees Celsius (32 degrees to 140 degrees Fahrenheit) for industrial applications.
Technical Specifications
| Brand | GE Automation Fanuc / Emerson Automation |
| Series | 90-70 |
| Part Number | IC697MDL940 |
| Description | Discrete output relay module |
| Number of I/O Points | 16 outputs |
| Output groups | Isolated / 2 groups |
| Rated voltage | 120/240 (47-63 Hz) VAC or 5/24/125 VDC |
| Relay type | Fixed coil, moving armature |
| Isolation | 1500 volts any output to backplane / 500 volts between Form C circuits or Form A groups |
| Output current | 2.0 amps from 5 to 265 VAC (maximum), 47-63 Hz / 2.0 amps from 5 to 30 VDC (maximum) / 0.2 amps from 31 to 125 VDC (maximum) / 0.2 amps from 31 to 150 VDC (maximum, Form A only) |
| Minimum load current | 10 mA |
| Output leakage current | 1 mA at 120 VAC |
| Protection (each output) | 3 amp fuse / Snubber (R = 47 ohms, C = 0.015 mfd) |
| Internal power consumption | 750 mA maximum from 5 volt bus on backplane |
| Weight | 860 g (1.9 lb) |
FAQ
Question: Does Automation Stop offer repairs on the IC697MDL940?
Answer: Yes. We offer repairs for the IC697MDL940 and it comes with our 1 Year Automation Stop Warranty.
Question: What type of warranty comes with the Emerson - GE Fanuc and IC697MDL940?
Answer: If you buy the IC697MDL940 through Automationstop.com it comes with our 1 Year Warranty and no other warranties.
Question: Can I buy the IC697MDL940 online?
Answer: Yes. Automation Stop sells the IC697MDL940 online and you can check out for the quantity and condition listed available above.
Question: What is the manufacturer for the IC697MDL940?
Answer: The IC697MDL940 is made by Emerson - GE Fanuc.
Question: What Brand does the Allen Bradley IC697MDL940 have?
Answer: The IC697MDL940 has a GE Automation Fanuc / Emerson Automation Brand.
Question: What Description does the IC697MDL940 have?
Answer: The Allen-Bradley IC697MDL940 has a Discrete output relay module Description.
Question: What Internal power consumption does the IC697MDL940 have?
Answer: The Internal power consumption of the Allen-Bradley IC697MDL940 is 750 mA maximum from 5 volt bus on backplane.
Question: What is the Isolation of the IC697MDL940?
Answer: The Isolation of the Rockwell-Automation IC697MDL940 is 1500 volts any output to backplane / 500 volts between Form C circuits or Form A groups.
Question: What Minimum load current does the Allen-Bradley IC697MDL940 have?
Answer: The Minimum load current of the Allen-Bradley IC697MDL940 is 10 mA.
Question: What is the Number of input/output Points of the IC697MDL940?
Answer: The Number of input/output Points of the IC697MDL940 is 16 outputs.
Question: What is the Output current of the IC697MDL940?
Answer: The Output current of the Allen-Bradley IC697MDL940 is 2.0 amperes from 5 to 265 VAC (voltage alternating current) (maximum), 47-63 Hz / 2.0 amperes from 5 to 30 VDC (maximum) / 0.2 amperes from 31 to 125 VDC (maximum) / 0.2 amperes from 31 to 150 VDC (maximum, Form A only).
Question: What is the Output groups of the IC697MDL940?
Answer: The Output groups of the IC697MDL940 is Isolated / 2 groups.
Question: What Output leakage current does the IC697MDL940 have?
Answer: The IC697MDL940 has a Output leakage current of 1 mA at 120 voltage alternating current (VAC).
Question: What unit Number does the Allen Bradley-Rockwell Automation IC697MDL940 have?
Answer: The Allen Bradley-Rockwell Automation IC697MDL940 has a unit Number of IC697MDL940.
Question: What Protection (each output) does the IC697MDL940 have?
Answer: The Protection (each output) of the IC697MDL940 is 3 amp fuse / Snubber (R = 47 ohms, C = 0.015 mfd).
Question: What is the Rated voltage of the IC697MDL940?
Answer: The Rated voltage of the IC697MDL940 is 120/240 (47-63 Hz) VAC (voltage alternating current) or 5/24/125 VDC.
Question: What Relay type is included with the IC697MDL940?
Answer: The IC697MDL940 has a Fixed coil, moving armature Relay type.
Question: What is the Weight of the IC697MDL940?
Answer: The Weight of the IC697MDL940 is 860 g (1.9 lb).
Series information for IC697MDL940
For additional information about IC697MDL940 check the data sheet or manual. Also check the manual PDF for all wiring diagrams, compatibility, troubleshooting, specifications, installation instructions, and accessories (such as batteries, terminal blocks, or cables) regarding IC697MDL940.
| Revision Part # | Also Known As | Availability |
|---|---|---|
| IC697MDL940A | IC697MDL940 Series A, Rev A | Request a Quote |
| IC697MDL940C | IC697MDL940 Series C, Rev C | Request a Quote |
| IC697MDL940D | IC697MDL940 Series D, Rev D | Request a Quote |
| IC697MDL940E | IC697MDL940 Series E, Rev E | Request a Quote |
| IC697MDL940F | IC697MDL940 Series F, Rev F | Request a Quote |
| IC697MDL940J | IC697MDL940 Series J, Rev J | Request a Quote |
Common Misspellings:
- IC697MDL94O
- ICG97MDL940
- ICG97MDL94O
- 1C697MDL940
- 1C697MDL94O
- 1CG97MDL940
- 1CG97MDL94O
