Allen-Bradley 2711C-F2M

The Allen-Bradley 2711C-F2M PanelView monochrome component graphic terminal has a 2-inches super-twisted nematic (STN) display which has a resolution of 122 x 32 pixels. This PanelView monochrome terminal operates with 04 function keys (F1 to F4) and 5 other which include up, down, left, right, and enter keys. The 2711C-F2M terminal contains a multiple-purpose serial RS-232 port which supports DH-485, third-party point-to-point and DF1 full-duplex communications with controllers using direct connections or modem connections. This terminal also includes both USB2.0 device and USB host port for the computer connecting to transfer applications, fonts, and images. The 2711C-F2M PanelView terminal contains a nonisolated RS-422/RS-485 port with 121 ohms terminating resistor which allows point-to-point communication using either full-duplex or half-duplex mode. The Allen-Bradley 2711C-F2M monochrome function keys terminal supports an input voltage rating range of 18 to 30 volts DC using a solid or stranded copper wire with a maximum power consumption of 5 watts. The 2711C-F2M terminal should be mounted in a panel which should be free of imperfections and flat without any tools or hardware to protect the internal circuitry and to maintain an adequate seal using panel clamps which automatically and easily latch when the terminal is plugged into the panel opening. This PanelView terminal can operate at a temperature range of 0 degrees to 50 degrees Celsius (32 degrees to 122 degrees Fahrenheit) and weighs approximately 0.19 kilograms (0.4 pounds) while shipping. The Allen-Bradley 2711C-F2M PanelView monochrome terminal is intended for use in a mainly industrial environment to monitor and control devices attached to a controller mainly MicroLogix, SLC™, and Micro800 controllers.

2711C-F2M is a PanelView Component C200 terminal by Allen-Bradley. For low-level applications with a serial connection, this component-level operator interface provides a control and visualization solution. Web application creates Human-Machine Interface (HMI) applications while your computer is connected directly to the terminal. The direct result shows on the terminal display without having to download it first. It has a size of 4.54 x 3.15 inches with an active display area of 1.93 x 0.55 inches. It has 2 inches of monochrome transreflective STN passive matrix display with a resolution of 122 x 32 pixels and a keypad for input. Keypad has four functions (F1, F2, F3, F4), up, down, left, right, and enter keys. It has a non-replaceable backlight with a minimum of 50,000 hours of life and yellow/green status indicator. It has an input voltage range from 18VDC to 30VDC with a nominal value of 24VDC, maximum power consumption of 5 watts, and heat dissipation of 16 British thermal units (BTU) per hour. It has a multipurpose RS-232 port which supports DF1 full-duplex communication with controllers using direct/modem connection, and DH-485 communication through a serial connection. Preferred controllers are MicroLogix, SLC, and Micro800. It also has an RS-485 port that supports point-to-point communication, a USB device port for maintenance or programming only, and a USB host port to power USB peripherals. It is connected to a browser using a USB port. Install the Allen-Bradley PanelView USB remote NDIS Network Device driver before connecting your computer to the USB port of the 2711C-F2M.

2711C-F2M is a PanelView Component C200 terminal by Allen-Bradley. For low-level applications with a serial connection, this component-level operator interface provides a control and visualization solution. Web application creates Human-Machine Interface (HMI) applications while your computer is connected directly to the terminal. The direct result shows on the terminal display without having to download it first. It has a size of 4.54 x 3.15 inches with an active display area of 1.93 x 0.55 inches. It has 2 inches of monochrome transreflective STN passive matrix display with a resolution of 122 x 32 pixels and a keypad for input. Keypad has four functions (F1, F2, F3, F4), up, down, left, right, and enter keys. It has a non-replaceable backlight with a minimum of 50,000 hours of life and yellow/green status indicator. It has an input voltage range from 18VDC to 30VDC with a nominal value of 24VDC, maximum power consumption of 5 watts, and heat dissipation of 16 British thermal units (BTU) per hour. It has a multipurpose RS-232 port which supports DF1 full-duplex communication with controllers using direct/modem connection, and DH-485 communication through a serial connection. Preferred controllers are MicroLogix, SLC, and Micro800. It also has an RS-485 port that supports point-to-point communication, a USB device port for maintenance or programming only, and a USB host port to power USB peripherals. It is connected to a browser using a USB port. Install the Allen-Bradley PanelView USB remote NDIS Network Device driver before connecting your computer to the USB port of the 2711C-F2M.